In order to avoid accidents, high-voltage distribution cabinet power outage is required to strictly follow the process steps of operation! The following edition will give you a brief introduction, I hope you have an understanding of this, in the future do not blindly operate, resulting in unnecessary trouble!

高压配电柜具体的停送电流程及注意事项如下：

Specific outage current flow and precautions for HV distribution cabinet are as follows:

1．接送电通知，到热电办理送电票。

1. Receiving and delivering telegram notice, transacting telegram ticket to thermoelectric power.

2．确认配电柜所在位置，了解其绝缘情况，确保可送电。

2. Confirm the location of the distribution cabinet, understand its insulation, and ensure that electricity can be transmitted.

3．检查接地刀所在位置，如已接地请断开，并检查机构是否复归。检查接地刀所在位置的方法：

3. Check the location of the grounding knife, disconnect it if it has been grounded, and check whether the mechanism has returned. Method of checking the location of grounding cutter:

4．检查断路器控制电源开关是否在合闸位置。

4. Check whether the power switch controlled by the circuit breaker is in the closing position.

5．检查断路器所处位置（工作/隔离）、状态（合闸/分闸）及储能情况，在将断路器小车摇进工作位置前保证断路器处于分闸状态、弹簧已储能。检查断路器状态的方法：检查储能情况的方法：

5. Check the position (work/isolation), state (closing/opening) and energy storage of the circuit breaker. Make sure that the circuit breaker is in the opening state and the spring has stored energy before rolling the circuit breaker trolley into the working position. Method of checking the state of circuit breaker: Method of checking energy storage:

断路器储能状态已储能未储能断路器上有储能指示位一个被拉开的弹簧一个未被拉开的弹簧

Energy storage status of circuit breaker

6．检查断路器二次侧插头是否已经插入并牢固。接地开关状态合闸分闸接地刀指示灯亮灭接地开关联锁装置打开封闭后门板接地开关联锁装置后门板可打开后门板不能打开断路器状态合闸分闸断路器状态指示灯红灯亮“｜”绿灯亮“━”断路器上的状态指示位合闸“┃”分闸“○”。

6. Check whether the secondary side plug of the circuit breaker has been inserted and secured. Grounding Switch State Switching, Grounding Knife Indicator Lighting, Grounding Switch Interlocking Device Opening Closed Back Door Plate Grounding Switch Interlocking Device Back Door Plate Opening Back Door Plate Can't Open Circuit Breaker State Switching, Circuit Breaker State Indicator Red Light Lighting, Green Lighting, and State Indicator Location Switching on Circuit Breaker Sluice.

7．用摇把将断路器小车摇进工作位置，确认断路器已经到位。

7. Roll the circuit breaker cart into the working position with a rocker to confirm that the circuit breaker is in place.

在用摇把摇小车的时候身体应避开断路器的观察窗，以免发生意外断路器从观察窗弹射出来对人体造成伤害。当摇把无法摇动且断路器工作位置指示灯亮时说明断路器小车已经到达工作位置。

When rocking the car with a rocking handle, the body should avoid the observation window of the circuit breaker in order to avoid accidental ejection of the circuit breaker from the observation window causing harm to the human body. When the shaking handle cannot be shaken and the indicator light of the circuit breaker's working position is on, it indicates that the circuit breaker cart has reached the working position.

8．通过综保确认断路器已经受电。

8. Confirm that the circuit breaker has been energized by comprehensive insurance.

9．操作完成，通知要求送电单位设备已经送电。

9. When the operation is completed, the notification requests that the equipment of the transmission unit has been delivered.

感谢您的阅读与观看，本文的精彩内容来自：山东航丰电缆桥架，我们会有更多的精彩内容继续为您呈现，详情请点击：http://www.sdhangfeng.com

Thank you for your reading and watching. The wonderful content of this article comes from: Shandong Hangfeng Cable Bridge, we will have more wonderful content to continue to show you. For more details, please click: http://www.sdhangfeng.com.