复合环氧树脂桥架在实际桥架使用中也可以称为是复合型玻璃钢桥架，其成型过程即玻璃钢制品的品质形成过程。由于复合环氧树脂桥架可以被看作是一种由多种材料组成的复合结构，因此生产对于复合环氧树脂桥架来说非常重要，而这种结构在制作过程中受到各种因素的制约。所以，制作方法虽然简单，但需要注意一些生产环境的细节，使得复合环氧树脂桥架在应用时更加，也对工艺和操作技能的要求更加。生产复合环氧树脂桥架时应注意以下四点生产环境要求。

Composite epoxy resin bridge can also be referred to as composite fiberglass bridge in actual use, and its forming process is the quality formation process of fiberglass products. Due to the fact that composite epoxy resin cable trays can be regarded as a composite structure composed of multiple materials, production is crucial for composite epoxy resin cable trays, which are constrained by various factors during the manufacturing process. So, although the production method is simple, it is necessary to pay attention to some details of the production environment to make the composite epoxy resin bridge safer in application, and also require more professional process and operation skills. When producing composite epoxy resin cable trays, the following four environmental requirements should be noted.

一、生产复合环氧树脂桥架位置

1、 Production of composite epoxy resin bridge positions

车间位置不宜建在水边，水边的环境太过潮湿，会影响生产桥架的湿度。生产复合环氧树脂桥架四周要注意防火，不得堆放可燃物，应留有消防车辆通道，并设消火栓。

The workshop should not be located near the water, as the environment near the water is too humid and can affect the humidity of the production bridge. Attention should be paid to fire safety around the production of composite epoxy resin bridge frames. Combustible materials should not be stacked, and there should be a passage for firefighting vehicles and fire hydrants installed.

二、防爆

2、 Explosion proof safety

车间电器灯具较好是防爆的，严禁在车间内临时乱接电线，过多的线路影响复合环氧树脂桥架生产的用电。

The electrical lighting fixtures in the workshop are explosion-proof and it is strictly prohibited to connect wires randomly in the workshop. Excessive wires will affect the electrical safety of composite epoxy resin bridge production.

三、消防设施

3、 Firefighting facilities

生产车间注意消防设施的合理安排，在厂房入口处设置灭火器、沙箱、消防毯，厂房附近设置水龙头。工场里的烟火。

Pay attention to the reasonable arrangement of fire protection facilities in the production workshop, set up fire extinguishers, sandboxes, and fire blankets at the entrance of the factory building, and set up faucets near the factory building. Fireworks in the factory.

四、生产温湿度

4、 Production temperature and humidity

可以为生产温度创造条件，使车间能达到调温调湿的目的，冬季大于15度，夏季小于30度，较好控制温度在20-25度之间，湿度应保持在75%以下，车间应放置干湿温度计，若是没有办法控制温度则可以经常开门窗通风，保持室内空气流通。

It can create conditions for production temperature, so that the workshop can achieve the purpose of temperature and humidity control. When the temperature is above 15 degrees in winter and less than 30 degrees in summer, it is better to control the temperature between 20-25 degrees, and the humidity should be kept below 75%. The workshop should place a dry and wet thermometer. If the temperature cannot be controlled, doors and windows can be opened frequently for ventilation to maintain indoor air circulation.

本文由济南电缆桥架友情奉献.更多有关的知识请点击:https://www.sdhangfeng.com真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article is dedicated by Jinan Cable Tray Friendship. For more information, please click: https://www.sdhangfeng.com Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned